Mega Glodok Kemayoran Lantai GF,Blok B5-05
Jalan Angkasa Kav.86 Jakarta Pusat
Telp/Hunting : (021) 29070732
Email : info@osmomarina.com

 
 
Customer Services
Popular Products
Pompa Ebara SQPB Cast Iron
Gear Pump GL Series Oriental Koshin
Alkon Robin Self Priming Pump
Vanco Mushroom Blower
Jainson Submersible Cable
HCP P4 Series 4" Submersible Deep Well Pump
Pedrollo 4SR Series Submersible Pump
Pedrollo 2CP Series Multistage Pump
Ebara DW VOX Series Submersible with Vortex Impeller
Ebara EVM Series Vertical multistage Pump


Product Name

JMP Marine Impeller Pumps JPR-D6500


 

JMP Marine Impeller Pumps JPR-D6500

INTRODUCTION

Flexible Impeller Pumps

Flexible impeller pumps provide an efficient solution to most marine pumping needs. The nprimary advantege of a flexible impeller pump is its Self-priming capability.

As the blades of the impeller are depressed and rebound, they create their own vacum drawing fluid into the pumps (see operating principle)

Pumps instatly with dry suction lift up to 3 meters, up t 9.5 meter when wet. Thus a flexible impeller pump being used in belge,deck wash, or engine cooling need not be located below the water  line or manually primed. An added features of flexible impeller pumps is that they can pass fairly large particles without clogging or damaging the pump. This reduces flexible the need for filtering the coming fluid.

A common feature of all flexible impeller pumps isthat they cannot be permitted to ru dry for more than 30 seconds easily replaceable, and service kits are available for all models.

 

FOR GOOD PUMPING

Pipe runs should always be kept as short and straight as possibl, avoiding rising and over obstructions, as this can create air-locks. Plumbing should be reinforced, non-collapsible hose of the recommended size.

Flexible impeller pumps must not be run dry (more than 30 seconds). Bilge pump water pump in particular should always be fastened to the boat structure to ensure their permanent location. Mount flexible impeller pumps so that some water is left in the pumpbody when the pump is off. This will prolog impeller life and speed priming. Pumps must be installed with the verboard discharge well above the waterline to avoid water syphoning back into the cessel.

 

FEATURE

-Strong bronze

-Long life mechanical seal

-High performance and long life flexible impeller

-Design with easy replacement of spare parts

-O-Ring seals at andcover (impeller cover) instead of gasket

 

OTHER

-Manufacturing pump to yous specification is available.(OEM)

-Please contact us dealers when you use for other application.

 

ENGINE COOLING PUMPS

JMP Corporation specialixed in manufacturing heavy duty raw water  pump, marine engine cooling pumps and spare parts more than 30 years. These are designed and manufactured especially for engine cooling applications. When you need specific engine cooling pumps please contact us.

-Powder Coated clutch surface to resist rust

 

Specification                                      JPR-D6500

-Port Size                                             2 Inch / Flange

-Impeller                                             ALBC

-Size (LxWxH,mm)                           370x185x185

-Weight (Appx)                                 20.0 kg

-Engine Model                                  DOOSAN – V158T, V158TI, V180TI, V222TI

 

 

-Service kits (replacement Part)are available

JMP Marine Impeller Pumps JPR-D6500

INTRODUCTION

Flexible Impeller Pumps

Flexible impeller pumps provide an efficient solution to most marine pumping needs. The nprimary advantege of a flexible impeller pump is its Self-priming capability.

As the blades of the impeller are depressed and rebound, they create their own vacum drawing fluid into the pumps (see operating principle)

Pumps instatly with dry suction lift up to 3 meters, up t 9.5 meter when wet. Thus a flexible impeller pump being used in belge,deck wash, or engine cooling need not be located below the water  line or manually primed. An added features of flexible impeller pumps is that they can pass fairly large particles without clogging or damaging the pump. This reduces flexible the need for filtering the coming fluid.

A common feature of all flexible impeller pumps isthat they cannot be permitted to ru dry for more than 30 seconds easily replaceable, and service kits are available for all models.

 

FOR GOOD PUMPING

Pipe runs should always be kept as short and straight as possibl, avoiding rising and over obstructions, as this can create air-locks. Plumbing should be reinforced, non-collapsible hose of the recommended size.

Flexible impeller pumps must not be run dry (more than 30 seconds). Bilge pump water pump in particular should always be fastened to the boat structure to ensure their permanent location. Mount flexible impeller pumps so that some water is left in the pumpbody when the pump is off. This will prolog impeller life and speed priming. Pumps must be installed with the verboard discharge well above the waterline to avoid water syphoning back into the cessel.

 

FEATURE

-Strong bronze

-Long life mechanical seal

-High performance and long life flexible impeller

-Design with easy replacement of spare parts

-O-Ring seals at andcover (impeller cover) instead of gasket

 

OTHER

-Manufacturing pump to yous specification is available.(OEM)

-Please contact us dealers when you use for other application.

 

ENGINE COOLING PUMPS

JMP Corporation specialixed in manufacturing heavy duty raw water  pump, marine engine cooling pumps and spare parts more than 30 years. These are designed and manufactured especially for engine cooling applications. When you need specific engine cooling pumps please contact us.

-Powder Coated clutch surface to resist rust

 

Specification                                      JPR-D6500

-Port Size                                             2 Inch / Flange

-Impeller                                             ALBC

-Size (LxWxH,mm)                           370x185x185

-Weight (Appx)                                 20.0 kg

-Engine Model                                  DOOSAN – V158T, V158TI, V180TI, V222TI

 

 

-Service kits (replacement Part)are available

JMP Marine Impeller Pumps JPR-D6500

INTRODUCTION

Flexible Impeller Pumps

Flexible impeller pumps provide an efficient solution to most marine pumping needs. The nprimary advantege of a flexible impeller pump is its Self-priming capability.

As the blades of the impeller are depressed and rebound, they create their own vacum drawing fluid into the pumps (see operating principle)

Pumps instatly with dry suction lift up to 3 meters, up t 9.5 meter when wet. Thus a flexible impeller pump being used in belge,deck wash, or engine cooling need not be located below the water  line or manually primed. An added features of flexible impeller pumps is that they can pass fairly large particles without clogging or damaging the pump. This reduces flexible the need for filtering the coming fluid.

A common feature of all flexible impeller pumps isthat they cannot be permitted to ru dry for more than 30 seconds easily replaceable, and service kits are available for all models.

 

FOR GOOD PUMPING

Pipe runs should always be kept as short and straight as possibl, avoiding rising and over obstructions, as this can create air-locks. Plumbing should be reinforced, non-collapsible hose of the recommended size.

Flexible impeller pumps must not be run dry (more than 30 seconds). Bilge pump water pump in particular should always be fastened to the boat structure to ensure their permanent location. Mount flexible impeller pumps so that some water is left in the pumpbody when the pump is off. This will prolog impeller life and speed priming. Pumps must be installed with the verboard discharge well above the waterline to avoid water syphoning back into the cessel.

 

FEATURE

-Strong bronze

-Long life mechanical seal

-High performance and long life flexible impeller

-Design with easy replacement of spare parts

-O-Ring seals at andcover (impeller cover) instead of gasket

 

OTHER

-Manufacturing pump to yous specification is available.(OEM)

-Please contact us dealers when you use for other application.

 

ENGINE COOLING PUMPS

JMP Corporation specialixed in manufacturing heavy duty raw water  pump, marine engine cooling pumps and spare parts more than 30 years. These are designed and manufactured especially for engine cooling applications. When you need specific engine cooling pumps please contact us.

-Powder Coated clutch surface to resist rust

 

Specification                                      JPR-D6500

-Port Size                                             2 Inch / Flange

-Impeller                                             ALBC

-Size (LxWxH,mm)                           370x185x185

-Weight (Appx)                                 20.0 kg

-Engine Model                                  DOOSAN – V158T, V158TI, V180TI, V222TI

 

 

-Service kits (replacement Part)are available



Related Products
Ebara 2CDX Spares centrifugal stainless steel
JMP Marine Impeller Pumps JPR-25UP
JMP Marine Impeller Pumps JPR-32LP And JPR-40LP
JMP Marine Impeller Pumps JPR-32UF And JPR-40UF

Pages 1 2 3 4 5 6 next


Copyright 2014 osmomarina.com All Right Reserved
Web Development by jasa website